The 80 concept called for a light, fast, elegant and comfortable super yacht, taking the
Cruiser / Racer concept to the next level - ‘Speed, seaworthiness, technology and innovation without compromise’. Nautor’s advanced ‘Regatta’ lay-up consists of S-Glass/ Aramid hybrid fibre with matched vinylester resin. The main construction parameters are weight reduction for speed, increase of strength for seaworthiness and reduction of noise and vibration for smooth and comfortable sailing.
Up to 10 guests in 4 cabins when two crew live forward.
CONQUISTADOR’s condition can quite simply be summed up in one word – stunning. She has been continually maintained and cherished her throughout her life by professional crew for very discerning owners. She has also had the benefit of numerous upgrades during construction and post building. These upgrades have been made with full consultation with the factory.
Maintained to exacting standards this Swan will appeal to an owner looking for the very best, whether they wish to cruise, race or charter – or all three!
Refit Winter 2016 / 2017.
New Awl grip paint on top sides and transom. Gold stripes with Flag blue.
All New bottom work, anti foul, propspeed, anodes, etc.
New OYS rod rigging package. Complete rig service and tune.
New Nav system and electronics; B&G Zeus wireless enabled touch screens at helm and nav station.
New Broadband B&G radar.
New precision compass and GPS antenna.
Upgraded onboard wifi system.
New and improved Northern Lights vibration and sound shield fitted.
WINTER: 2016/2017Basically everything that can be serviced, IS being serviced! Water maker, refrigerator system, AC system, Navtec system, BowThruster, Gori propeller, the list goes on!
2016 New Bimini's, dodger and sail cover
October 2011 to August 2012.
A very extensive refit was carried out while in the RMK yard in Turkey
The renewal of the teak decks and paint work were contracted by RMK whilst all further upgrades, replacement and refurbishment of systems was carried out by Nautor trained technicians. The list of issues that was addressed is too long to put into a specification. Just the highlights are listed below.
- 2012 – new Max Power retractable bow thrusters, hydraulic, 30hp
- 2012- full service on the Navtex system and all hydraulics.
- 2012- new teak decking throughout.
- 2012 – interior; new headliners, New Sunbrella floorcovers, new salon leather upholstery, new crew area upholstery, new mattresses in owner's cabin. New varnish where required. Wooden bunk in crew area. ( winter 2012).
- 2012 - new custom made pedestals at both steering columns with all controls such as furling, lights, thrusters, navigation, autopilot etc. looking very smart.
- 2012 – new design and manufactured steering consoles.
- 2012 – new AC, chilled water unit 72000 Btu with 7 air handlers.
- Replaced hydraulic hatch pistons
- 2012 - New Yanmar Main engine 4LHSTP, 240 Hp-. by Peter.fi
- 2012 – New Northern lights Generator, 20 Kw/hr.
- 2012 - New cush plate
- 2012- all biminis and dodgers new.
- 2012 – new carbon protection plates at Bow and Stern
- 2012 – new Anchor Chain, galvanized 100Mt.
- 2012 – toilets 4 x Tecma 24v, new.
- 2012 – 7 new Groco Brass seacocks in the engine room.
- 2012 – refrigeration, Penguin 24v, new.
- 2012 – new Lewmar V6 windlass
- 2012- new cruising Genoa from Doyle, mainsail sheet.
- 2012 – lopo lights on bow, stern and masthead.
- 2012- galley equipment upgrades: Miele induction stove and oven, Miele washer/dryer. Galley macerator.
- 2012- new dive compressor.
- 2012 – new tender Ribeye 4.3 M.
- 2012- new propshaft-
- 2012- Awlgrip paint on hull, topsides and super structure. RMK-
- 2012 – re machined Gori prop. Serviced and balanced by Gori.
- 2012 – navigation instruments upgrades and repairs: Displays all reconditioned, new speedlog, Navnet2 Plotter replaced, furuno plotters, radar and SSB radio full serviced by “Diverse”. 2 x new Furuno VHF. Autopilot new display and remote
Other Upgrades and Modifications:
- Added removable carbon bow sprit for easier use of asymmetric code “0” and added an extended carbon spinnaker pole for racing (07/2006)
- Upgraded and modified lightning protector to a lightning dissipater system (02/2001)
- Replacing computer and wireless system 2007/08
- Replacement of batteries to Gel type
- Waterpump Giamesschi ecojet 2
- Any pump that had faults was replaced as needed same, plumbing and hoses.
- New cleats, 6 x Versari del Monte.
- 2012 – service on all sails.
- All fairleads re anodized and moving parts replaced.
- Steering wheels covered in Carbon leather look.
- Doyle Stratus Main, new 2014
- Doyle genoa, new 2013
HULL & DECK
The construction is partly high tech with honeycomb cored pre-pregnated carbon fibre structural bulkheads and main deck. Carbon fibres are used to reinforce the hull stiffeners.
Hull construction is of proven solid single skin glass fibre reinforced Vinylester laminate.
Coloured topsides, originally in gel coat dark blue (instead of standard white) - repainted to Awlgrip Majestic blue (June 2012).
Cove stripe and boot top painted in Pale Gold Awlgrip.
Bottom paint, International Micron Extra, black.
Transom and deck extended by 45 cm to give an aft deck of 1,65m at build stage.
Racing keel fitted (06/2002) in Brisbane
Rudder and steering system:-
Carbon fibre spade rudder with two self-aligning roller bearings
Two steering wheels standard 120cm carbon/teak
Weed cutter forward of the rudder post
Rudder serviced and rubber seal replaced 2012 RMK
Rudder dropped and inspected
Keel removed and resealed 2012, new keel nuts.
Honeycomb cored pre-preg carbon fibre structural bulkheads and main deck.
Toe rail was lengthened forward to create foothold for the people on the bow.
Teak replaced to original specification 2012
Teak foot rests at helm
Winches, power pack, & windlass:
Winches all upgraded from standard package:
Primary winches 2 x Harken 1110.3TCA hydraulic, 2 x top cleat with top drive,
connected to 2 removable pedestals.
Secondary winches 2 x Harken 1110.3 STAHY, hydraulic self tailing with top drive.
Main sheet winch Harken 1110.3STA, hydraulic self tailing with top drive,
Main sheet system with main sheet winch, plus main sheet track, stoppers, blocks and
Traveller winches 2 x Harken 48.2 STA.
Removable pedestal for mainsheet winch
Halyard winches 2 x Harken 980.3 STAHY, hydraulic, self-tailing including black
anodised aluminium base to be added under the winches on deck.
Additional utility winches - 2 x Harken B74.2 STA
Additional snubbing winch on centreline aft of mast, Harken 812C
Harken Power Pack, Hydro 8,9 (instead of standard Lewmar Commander), for following units:
Secondary winches x 2
Primary winches x 2
Halyard winches x 2
Main sheet winch
Hydraulic hose (for later installation of head sail furling unit)
Parker Kevlar hydraulic hoses.
Emergency ‘stop’ switch for hydraulic winches located at both steering wheels.
Primary, secondary and main sheet drum bases upgraded and replaced by Harken (09/2006).
Fittings for running rigging:
Roller bearing stand up lead blocks at mast foot, 10 pcs, no lines under deck.
Additional pair of genoa tracks, including cars.
Mainsheet track with cars on bridge deck.
Fore guy foot block aft of the anchor windlass hatch and a stand up block on fore deck.
Aft guy blocks moved outboard to the bulwarks just forward of the lifeline gate, both sides.
Spinnaker barber hauler pad eyes, each side, aft of the gate, Wichard 6506.
Headstay tack fittings, 2 pcs, (no furling unit).
Double genoa turning blocks 2 x Harken H5073 base plates reinforced (09/2000).
Fore guy (2:1) pad eye 200mm.
Nautor made, stainless steel threaded deck sockets and screw in eyes for stand up
Harken block at foredeck area. New soft shackles throughout.
Deck fittings for carbon fibre spi pole, carbon fibre jockey pole and for carbon racing pole.
Recessed 16” mooring cleats (bow, stern and amidships). Versare del Monte.
Fold-up seat on pushpit, both sides.
Carbon fibre radar post mounted through deck, removable and with quick connection for the cable including cover.
Bathing ladder / side boarding ladder with teak steps.
Screw in pad-eyes for the dinghy.
Stainless steel chafing plate at anchor chain inlet at the carbon arm.
Shore power intakes through a small hatch in port side of the transom for the cables with the connection in the lazarette.
Modified aft end of bridge deck with cut-out at main sheet winch.
Deck prisms over the heads forward of mast.
Aft deck hatch to lazarette.
Removable carbon cover for the bridge deck hatch, with a foot rest in the middle.
Storage locker for 2 - 8-person soft pack life raft and other safety equipment port side of companionway.
New Harken push buttons on deck.
Interior forepeak fittings:
Two rails in the forepeak, one each side high up beside the chain locker (along ships, above the level of the chain locker inspection hatch).
Hanging rails for storage of spare sheets. Halyards and mooring lines.
Rail in the gas locker. Rail on the forward bulkhead in the forepeak.
Bracket for stowage of a 25 hp short rig outboard engine in the forepeak.
Yanmar 4LHSTP, 4 cilinder, 240Hp, new 2012. 2350 engine hours at January 2017
3 blade Gori folding propeller, serviced 2017
Accessories on engine:
Heat exchanger for the consumable fresh water is included in the same circuit, making hot water available whenever the engine is running.
Service alternator, replaced (10/2006).
Engine bed reinforced – Villefranche (02/2007).
Main engine exhaust outlet at the transom.
Wet exhaust system with fibreglass silencer and gas/water separator for main engine and diesel generator, cooling water is discharged below waterline, exhaust gases, discharge through transom.
Exhaust system replaced 07/2012 for both main engine and gen set.
Fuel volume 2000 Litres in stainless steel tanks.
Racor 75/500 FGX P 10 for the engine and
Racor 500 FG P for the diesel generator.
Fuel filter / water separator with alarm.
Racor fuel filter replaced and installed new set (09/2002).
PLUMBING AND VENTILATION
Forced air ventilation in cabins.
Exhaust ventilation in heads and galley and engine room.
Replaced aluminium vent grill to fibreglass in centre cockpit (06/2002).
Water maker, Sea Recovery Aqua Whisper, 4,500 litres 1200 gallons per day. Serviced 2017
Integrated stainless steel water tanks.
Deck shower at bathing platform aft.
Fresh water connection to deck washes outlets amidships starboard and in anchor well.
Deck wash outlets fore and aft.
Black water system:
Linked to the two toilets aft (Day head and Owners) approx. 200 litres.
Forward holding tank linded to crew and forward heads, approx 70 litres
Battery capacity 1200Ah / 5h, (600 for radios, 600 for service).
Additional 24V outlet on the aft edge of the galley vent Dorade box forward of the mast and steering wheel pedestal.
Additional 230V outlet in the locker starboard side of the main entrance for chargers.
Shore power 230V and 115V via 6kVA transformer.
Separate shore power inlet for air conditioning 230V 50A,
(each inlet is provided with polarity alarm)
Inverters and chargers in aired location.
Inverter, Mass 24/500 VA, 230V including transfer switch.
Inverter for entertainment equipment, Mass 24/1500 VA, 230V including transfer switch.
24V deck outlets selectable 24/12V.
20Kw/hr Northern lights, new 2012. 3675 gen hours at January 2017. A new and improved Northern Lights vibration and sound shield is being fitted Jan 2017
Hella Turbo fans, 12 pcs, positioned as:
Crew cabin x 2; Engine room x 2; Owners cabin x 2
Port aft cabin x 2; Navigation station x 1; Port forward cabin x 1
Galley x 1; Captains cabin x 1
Windex light, Boom light,
Lights in the bar unit in saloon,
Navigation lights with switch to alternative power source,
Lights on radar post, forward and aft,
Rheostat for boom lights,
Ice Maker run by inverter 24 VDC/220 VAC.
Clima AC chilled water system, 72.000 BTU, 230V, 50Hz with 7 air handlers.
All new 2012. Serviced 2017
Panels and controls
Battery Ah capacity meter DCC 4000.
Thermostat controlled fan for instruments at navigation station.
Flow monitor for cooling water for main engine and diesel generator cooling water.
Separate engine control panel in cockpit
All controls for windlass, transom door, furling, deck lights and horn on helm stations.
Leather on the saloon sofas, chairs and navigation seat, new 2012.
Leather for vanity stools, same as in saloon.
Upholstery material for mattresses, Annala, Helmi.
New mattress owners cabin 2012.
Upholstery material for settee in fo’c’s'le / crew area, imitation leather.
Canvas lee cloth for all berths.
Canvas covers for all leather cushions for use during delivery and racing.
Oilskin locker aft of skipper’s cabin starboard, with shelves outboard and hanging rail.
Teak hooks for hanging lockers, 12 pcs.
Sunbrella and rubber floor protection on all except master cabin new 10/2012.
Modifications to standard and general fittings and description:
Fo’c’s'le locker. Storage stainless bars for sheets, etc.
Workbench on starboard side, mattress to fit on top.
Upper bunk in teak.
Hanging locker starboard side aft with 2/3 and 1/3 deep shelves outboard.
2 crew beds
Port forward guest cabin: 2 + Pullman
Double lower berth, mattress in one piece, upper Pullman berth.
Hinges on the outboard and inboard section under the berth, in three sections to get access to the stowage under the bed.
Lockers outboard accessible when Pullman down. Lockers under the bed.
Utility shelf at the head end of the upper berth.
Hanging locker 2/3 hanging, 1/3 shelves behind hanging space.
Port aft guest cabin: 2 singles + Pullman
Fixed berths each side with Pullman above outboard berth.
Lockers outboard accessible when Pullman down.
Drawers under both berths. Upper lockers above inboard berth.
Hanging locker with 2/3 and 1/3 shelves behind hanging space.
Water thermos next to berths x 2.
starboard aft of saloon, Guest or Captains cabin. Single + Pullman
Fixed lower berth and Pullman upper berth,
10cm foam mattresses (instead of spring mattresses)
Hinged lids to the space under the bed.
Utility shelf at head end of the upper berth.
Hanging locker aft with shelves in the lower part, hanging space in the upper part.
Water thermos next to bed.
Foul weather gear and safety harness locker aft of Capt.’s cabin (port side).
Owner’s Cabin Aft - 2
Centreline berth, drawers under the bed.
Full-length clear mirror flush with the forward bulkhead.
Light switches and air conditioning control each side of the mirror.
Vanity stools hinged on port and starboard side.
Mirror in port side vanity lid.
Hanging lockers 2/3 hanging, 1/3 shelf and shelf behind the hanging space outboard.
Book shelves on both sides, port side.
Water thermos, 2 pcs, one each side of the bed.
Drawers each side aft of the bed.
Bar unit with top loaded drink fridge and icemaker on port side aft with glass stowage on one side and bottles on the other (mirror back wall in bottle locker).
Three separate roller shutters in front of entertainment units on starboard side.
Stowage for CD’s. Pull out crockery drawer forward on starboard side.
Locker outboard of this locker for linens. Book shelves between the two lockers on port side.
Three chairs at main saloon table, with locks for anchoring.
Saloon table on starboard side, removable, stowage space under the table base.
Space under locker on starboard aft of the settee dedicated to computer gear & outlets etc.
Stowage space inside the port saloon table base.
Stowage space under the saloon port side sofa forward (houses the Owner’s manuals).
Opening lockers to the narrow space outboard of the companionway ladder.
New Tecma heads throughout 2012
Toilets on port side aft made into one larger toilet, and separate shower stall access also from the port aft guest cabin.
Overhead shower and hand shower unit in crew toilet and captain’s toilet.
Utility shelf in Owner’s shower stall.
Soap holders in all heads.
Shower curtains in the port fwd toilet and in the starboard aft toilet.
Counter tops Corian, Cameo off white.
Draining locker for plates.
Miele induction 4 burners with Miele oven, new 2012
Icemaker Hoshizaki 230V – installed in saloon, including carbon filter.
Upper and lower fridges and freezer in galley
Drinks fridge in saloon
24v system installed by Penquin Refridgeration in 2012
Chart stowage in teak box above navigation area.
Table lid, chart table lid and outboard lid with leather covers.
Instrument console at the inboard forward corner of the chart table.
Space for a computer keyboard.
Navigation station seat.
Small teak shelf with a teak rail, 10cm under the outboard top opening lid, 15cm deep.
Teak rail across, inside the navigation desk.
Overhead paper charts storage locker.